With the application of steel structure and the progress of technology and the development of social economy, many markets are developing continuously, and the demand of the market is more and more extensive. But we are also concerned about safety. So we should do a good job of safety. The first is the processing technology of steel structure components which can prevent accidents in the future. So what should we pay attention to in the process of making steel structure?

　　儲存的鋼鐵

　　Stored steel

　　鋼結構的貯存要求盡量減少鋼的變形和腐蝕，使鋼節堆放時盡量向后或向外，有利于排水。在正式入庫前進行嚴格的檢驗，檢驗合格后方可辦理入庫手續。

　　The storage requirement of steel structure is to minimize the deformation and corrosion of steel, so that the steel knots can be stacked backward or outward as far as possible, which is conducive to drainage. Strict inspection shall be carried out before formal storage, and the warehousing formalities shall be handled only after the inspection is qualified.

　　鋼結構加工要點

　　Key Points of Steel Structure Processing

　　1. 必須按照加工工藝流程進行。有隱蔽焊縫時，必須焊接后方可合格;

　　1. Processing process must be followed. When there are concealed welds, they must be welded before they are qualified.

　　2. 裝配時行小零件的裝配，再進行大零件的裝配，糾正后再進行裝配，防止大零件變形;

　　2. Small parts are assembled first, then large parts are assembled. After correction, large parts are assembled to prevent deformation.

　　3.裝配零件時，應檢查零件是否合格，并在30-50mm范圍內邊緣油漬和污垢;

　　3. When assembling parts, check whether the parts are qualified and remove grease stains and dirt from the edges within 30-50 mm.

　　4、在裝配輪胎時，必須考慮預釋放焊后的收縮和加工余量;

　　4. When assembling tires, the shrinkage and processing allowance after pre-release welding must be considered.

　　5、鋼結構在生產過程中應將頂部密件拋光，使其接觸面達到75%;

　　5. In the process of production, steel structure should polish the top part to make its contact surface reach 75%.

　　6、加工零件要編號，寫清圖號、零件號等便于查找;

　　6. Processing parts should be numbered, and drawing numbers and parts numbers should be clearly written for easy searching.

　　7. 板件和型材的裝配和焊接也要按順序進行，如零件的隱蔽部位要提前噴漆。

　　7. The assembly and welding of sheets and profiles should also be carried out in sequence, such as painting the concealed parts in advance.

　　因此，在鋼結構加工過程中，必須嚴格執行各種工藝和步驟，才能生產出合格的鋼結構構件。

　　Therefore, in the process of steel structure processing, it is necessary to strictly implement various processes and steps in order to produce qualified steel structure components.